D-PDC-DY-23 Study Guide: Latest [Dec 14, 2024] Realistic Verified D-PDC-DY-23 Dumps

D-PDC-DY-23 Questions & Practice Test are Available On-Demand

NEW QUESTION # 70
Which field in an IP header is used for QoS marking?

• A. ToS
• B. CoS
• C. Options Header

Answer: A

NEW QUESTION # 71
Two OS10 switches reside within a VLT domain with statically configured primary- priorities. The current primary peer, switch OS10-A, has a priority of 100, while the secondary peer, OS10-B, has a priority of 200.
If OS10-A reboots and comes back online, what roles will the VLT peers be assigned?

• A. OS10-A will be secondary and OS10-B will be primary.
• B. OS10-A will be primary and OS10-B will be secondary.
• C. OS10-A will be standby and OS10-B will be primary.
• D. OS10-A will be secondary and OS10-B will be master.

Answer: A

NEW QUESTION # 72
The destination O E2 144.254.32.0/24 appears in the routing table of a switch.
What is true for this route?

• A. There are two (2) egress paths with equal costs to the destination
• B. The network represents an OSPF inter-area route
• C. It is a non-native OSPF route
• D. The route has been redirected from eBGP

Answer: C

NEW QUESTION # 73
Using the MAC 8c-ec-4b-5b-61-9d, what is a valid EUI-64 link local address?

• A. fe80::a9:8eec:4bff:fe5b:619d
• B. ff80:a9:8eec:4bff:fe5b:619d
• C. fe80::a9:8cec:4bff:fe5b:619d
• D. 2001::a9:8eec:4bff:fc5b:619d

Answer: A

NEW QUESTION # 74
Refer to the exhibit.

No static routing has been configured. For iBGP loopback-based peering, which statement is correct?

• A. It is not necessary for the routing table on S1 to have an entry for the loopback network of S3.
• B. For iBGP peering, physical interface addresses must be used.
• C. A static route on S1 to 144.254.32.1/32 will eliminate the need for loopback-based peering with S3.
• D. S1 should have the Loopback network of S3 in its routing table for loopback-based peering.

Answer: D

NEW QUESTION # 75
What is a characteristic of a static LAG on a Dell Networking OS10 switch?

• A. Uses LACP for management only
• B. Does not allow reconfiguration of the predefined ports
• C. Does not use any protocol for configuration and management
• D. Uses LACP for configuration only

Answer: C

NEW QUESTION # 76
What is one of the configuration requirements for VLT on OS10?

• A. Create a VLT domain on each peer using the vlt-domain command.
• B. Configure a port channel for VLTi
• C. Configure a time interval to delay bringing up VLT ports after reload when the VLTi is turned on after failure.
• D. Manually reconfigure the VLT MAC address. Configure the VLT MAC address on both VLT peers.

Answer: A

NEW QUESTION # 77
Which best describes traffic flow in a campus network environment?

• A. South-West
• B. North-South
• C. North-East
• D. East-West

Answer: D

NEW QUESTION # 78
Of the following descriptions, which two describe SmartFabric Services components. (Select 2)

• A. The CPS distributed databased contains target configurations for all devices.
• B. An SFS Controller is an endpoint that sends configuration changes to the fabric Primary.
• C. SFS Agents exist on all fabric switches except the current Primary.
• D. Each fabric switch's local CPS database is advertised into the fabric.
• E. The External Fabric Manager does not employ an SFS Agent.

Answer: A,E

NEW QUESTION # 79
When the show ip bgp neighbors command is issued, which BGP slate reflects a successfully created adjacency with another BGP peer?

• A. Full
• B. Peering
• C. Active
• D. Established

Answer: D

NEW QUESTION # 80
What version of IGMP is required by PIM-SSM receivers?

• A. IGMP snooping
• B. IGMP 2
• C. IGMP 3
• D. IGMP 1

Answer: C

NEW QUESTION # 81
How does NIC teaming provide load balancing and failover?

• A. Multiple NICs on multiple servers act as a single virtual network adapter port.
• B. Multiple NICs on one server act as a single virtual network adapter port.
• C. Multiple NICs on one server act independently as multiple virtual network adapter ports.
• D. Multiple NICs on multiple servers act independently as multiple virtual network adapter ports.

Answer: B

NEW QUESTION # 82
Refer to the exhibit.

Which three commands are used when deploying an automated Leaf and Spine topology using SFS?
(Select 3)

• A. Spine1(conf)# smartfabric l3fabric enable role SPINE prefer
• B. Leaf1(conf)# smartfabric l3fabric enable role LEAF vlti ethernet 1/1/10
• C. Spine1(conf)# smartfabric l3fabric enable role SPINE
• D. Leaf2(conf)# smartfabric l3fabric enable role LEAF vlti ethernet 1/1/10
• E. Spine1(conf)# smartfabric l3fabric enable role SPINE downstream ethernet 1/1/1-1/1/2

Answer: A,B,D

NEW QUESTION # 83
Which command shows whether a LAG protocol is static or dynamic on a Dell EMC Networking OS10 switch?

• A. show interface port-channel summary
• B. show running-configuration lacp
• C. show port-channel summary
• D. show lacp neighbor

Answer: C

NEW QUESTION # 84
In OS10 what is a downside of enabling strict priority queuing?

• A. Other queues are not serviced
• B. Network congestion occurs, strict priority queuing increases the likelihood that egress traffic from the strict priority queue will be dropped
• C. The CAM table becomes saturated
• D. System scheduler causes high NPU utilization

Answer: A

NEW QUESTION # 85
What is the purpose of the VLT backup link?

• A. To monitor the availability of the VLT peer if there is a VLTi failure.
• B. To monitor the VLT internal control VLAN on the VLT peer if there is a VLTi failure.
• C. To synchronize MAC address tables bel ween VLT peers if there is a VLTi failure.
• D. To synchronize ARP entries between VLT peers if there is a VLTi failure.

Answer: C

NEW QUESTION # 86
......

Valid D-PDC-DY-23 Exam Dumps Ensure you a HIGH SCORE: https://prepaway.dumptorrent.com/D-PDC-DY-23-braindumps-torrent.html